EP8020
STEAM GENERATOR IRON
PROFESSIONAL TYPE IRONING SYSTEM
WITH DETACHABLE WATER TANK
FOR HOUSEHOLD USE ONLY
USE AND CARE INSTRUCTION MANUAL
READ BEFORE USING THE IRONING SYSTEM
CONGRATULATIONS!
YOU ARE THE OWNER OF THE ULTIMATE IN MODERN IRONING AND PRESSING
EQUIPMENT. FOR YOUR SAFETY AND TO FULLY ENJOY THE ADVANTAGES OF
YOUR APPLIANCE, PLEASE TAKE A FEW MINUTES TO READ ALL THE IMPORTANT
SAFEGUARDS AND “USE & CARE INSTRUCTIONS”. KEEP THIS MANUAL HANDY
FOR EASY REFERENCE. PLEASE REVIEW THE PRODUCT WARRANTY AND MAIL
THE OWNER REGISTRATION FORM
EURO-PRO Operating LLC
94 Main Mill Street, Door 16
Plattsburgh, NY 12901
USA
EURO-PRO Operating LLC
4400 Bois Franc
St. Laurent, Quebec H4S1A7
CANADA
IMPORTANT SAFEGUARDS
When using your Steam Generator Iron, basic safety precautions should always be followed.
Read carefully the following instructions as they provide important information concerning how to
install, use and care for this appliance.
1. Use steam generator iron only for its intended use.
2. Use ironing system only for its intended use.
3. To protect against a risk of electric shock, do not immerse the iron or any part of the ironing
system in water or any other liquids.
4. The ironing system (iron and steam generator) should always be turned OFF before plugging
into or unplugging from wall outlet. Never pull power cord to disconnect from outlet; instead,
grasp plug and pull to disconnect.
5. Do not allow cord to touch hot surfaces. Let the ironing system cool completely before putting
away or opening water tank (removing safety cap). Wrap cord loosely around the ironing
system when storing.
6. Always disconnect ironing system from electrical outlet when filling with water or emptying and
when not in use. Always turn the safety cap slowly when opening the water tank.
7. Do not operate the ironing system with a damaged cord, plug or if the iron or any other part of
the system has been dropped or damaged. To avoid risk of electric shock, do not
disassemble or attempt to repair the ironing system. Return the unit to EURO-PRO
Operating LLC (see warranty) for examination, repair or replacement. Incorrect reassembly
or repair can cause a risk of electrical shock or injury to persons when the ironing system is
used.
8. Close supervision is necessary for any appliance being used by or near children. Do not
leave ironing system unattended while connected or while on an ironing board. Always
position the iron flat on the silicone rubber posts.
9. Burns can occur from touching hot metal parts, hot water or steam. Use caution when turning
the system upside down, as there may be hot water in the unit. Never direct steam at any
person, especially when using the iron in the vertical position. The steam is very hot and can
cause burns.
10. The hot iron base (soleplate) must always rest on the non combustible silicone rubber rests on
top of the steam generator.
11. Do not operate in the presence of explosive and/or flammable fumes.
12. This appliance is intended only for household use. Follow all user instructions in this manual.
WARNING: The power cord on this product contains lead, a chemical known to the State of
California to cause birth defects or other reproductive harm. Wash hands after handling.
SPECIAL INSTRUCTIONS
1. To avoid a circuit overload, do not operate another high-wattage appliance on the same circuit
simultaneously with the steam generator iron.
2. If an extension is absolutely necessary, a 15-ampere rated cord with a polarized plug should be
used. Cords rated for less amperage may overheat. Care should be taken to arrange so that it
cannot be pulled on or tripped over.
3. Do not leave iron unattended when the system is connected to a power supply/electrical outlet.
This appliance has a polarized plug (one blade is wider than the other).
POLARIZED PLUG:
As a safety feature, this plug will fit into a polarized outlet only one way. If
the plug does not fit fully into the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician. Do not attempt to defeat this safety
feature.
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
Rev. 06/01B
1
Even if you have used a steam generator iron before, please read all instructions and safeguards
in the Use and Care Instruction Book. In addition, please note the following user tips:
USING STEAM
PLEASE NOTE: Steam performance improves after the first 6-8 hours of usage. The steam
power increases and initial condensation at maximum temperature is reduced.
1. Make sure the temperature setting of the iron is within the steam range on the temperature
selector.
2. Turn power on for iron and steam generator. Before starting to use steam, make sure the
Steam Ready Light (2) is “ON”, indicating that steam is available.
NOTE: Trying to use steam before the Steam Ready Light (2) is “ON” can cause water
drops in the steam coming out of the iron.
CLEARING THE INITIAL CONDENSATION:
3. Clear the initial condensation by pressing the Steam Button (A) up to 3 seconds. Repeat if
necessary.
IMPORTANT NOTE:
4. While using the ironing system, if steam has not been released for more than approximately
5 minutes, the hose has cooled and any steam remaining in the hose from the last use
might condense. Clear this condensation by pressing Steam Button (A) before proceeding
to use the iron.
2
STEAM GENERATOR IRON
MODEL EP8020
14
h
13
Steam Tank (Base)
Iron
1. Steam On/Off Rocker Switch
2. “Steam Ready” Indicator Light
3. Water Level Indicator Light
4. Iron On/Off Rocker Switch
5. Steam Pressure Valve
a. Steam Button
b. Continuous Steam Lock-on Button
c. Temperature Control Knob
d. Cork Handle
e. Steam Hose
6. Iron Rest
7. Steam Base Tank
f. Temperature Indicator Light
g. Soleplate
8. Locking Device (Used for Tank Removal)
9. Removable Water Tank
10. Rotating Cap, Used to Add More Water
11. Steam Control Knob
h. Litmus Paper (See Instructions to Check
Water Hardness, Page 4)
12. Power Cord
13. Key to Open Steam Pressure Valve (#5)
14. Cord Holder
3
STEAM GENERATOR
IMPORTANT SUPPLEMENTARY USER INFORMATION
Read all instructions before using the Steam Generator Iron and follow all instructions and
safeguards carefully.
1. A WORD ON WATER
Check the water hardness in your home with the litmus paper. (Please note that you can only
use the litmus paper once.)
a) Immerse the litmus paper in a glass of water for one second.
b) Wait until the paper is dry and refer to the scale here below.
ꢀ ꢁ ꢁ ꢁ soft water
ꢀ ꢀ ꢁ ꢁ medium hard water
Use tap water
ꢀ ꢀ ꢀ ꢁ
ꢀ ꢀ ꢀ ꢀ
hard water
very hard water
Use demineralized/distilled water
For best results EURO-PRO recommends using 100% demineralized/distilled water.
DO NOT USE WATER PROCESSED THROUGH A HOME WATER SOFTENING SYSTEM
OR BOTTLED MINERAL WATER.
If you choose to use regular tap water, make sure that the chloride (CL) level of your local water
supply does not exceed 8mg/liter. In many areas, the chloride level exceeds 8mg/liter. Use of
tap water with high chloride levels will adversely affect the life expectancy of your steam
generator. Tap water can be mixed with demineralized/distilled water to lower the chloride level.
For best results make sure to use the right proportions to bring the chloride level to 8mg/liter or
less.
2. FOR BEST RESULTS DO NOT LEAVE HOT IRON RESTING IDLE ON IRON REST (6)
FOR LONG PERIODS OF TIME
The life-span of your EP8020 will be reduced if the iron is left idle at high temperatures for
extended periods. If iron is not in use, reduce its temperature to the lowest temperature setting
on the Temperature Control Knob (c).
3. WARRANTED FOR REGULAR HOUSEHOLD USE
While the EP8020 is a professional type ironing system, it is intended for and warranted only
for normal household use. Iron and/or steam generator should not be used for more than 15
hours per week in approximately 3 hour intervals.
4
INSTRUCTIONS FOR USE
Your new Ironing System offers the ultimate in modern ironing. Read carefully all the important
safeguards (page 1) and all the instructions in the user manual before using your Ironing
System. Follow all the instructions.
1. WARNINGS:
• Never leave the unit unattended while plugged in. Always disconnect from electrical power
source.
• You must always unplug (disconnect) the unit when you have finished using it and:
A) Before any cleaning or maintenance.
B) Before filling and emptying the water tank/steam generator.
C) When you leave the room, even if only for a few minutes.
• Always place the iron on the iron rest (6) when not in use.
• Never use the ironing system if the iron or the steam generator have been dropped. To avoid risk of
electric shock, do not disassemble or attempt to repair the ironing system. Return the unit to EURO-PRO
Operating LLC (see warranty) for examination, repair or replacement.
• Do not stretch out the power cord (12) and/or steam hose (e) while ironing. Do not use the appliance if
a power cord (12) and/or steam hose (e) is damaged. If the power cord (12) or steam hose (e) show
signs of wear or damage, please return the unit to EURO-PRO Operating LLC (see warranty) for
examination, repair or replacement.
• Read the “IMPORTANT SAFEGUARDS” listed on page 1 and all special instructions and follow carefully.
2. DRY IRONING:
1. Place your steam generator on a solid flat surface.
2. Plug in unit. Press the Iron ON/Off Rocker Switch (4) which lights up to indicate that the iron is “ON”.
3. Set the Temperature Control Knob (c) according to the garment label or use the temperature setting
table included in the user’s manual as a guide.
4. The Temperature Indicator Light (f) will go on and will turn off when the iron has reached the desired
temperature.
5. You may iron without steam at any temperature setting.
3. IRONING WITH STEAM:
1. Plug the appliance into a 110/120 V electrical outlet.
2. Press the Iron ON/Off Rocker Switch (4) to the “ON” position. Press the Steam ON/OFF Rocker
Switch (1) to activate steam generator.
3. When planning to use steam, make sure to set the Temperature Control Knob (c) in the area
designated for use with steam. i.e. between the two “ ” and three “ ” dots on the Temperature
Control Knob (c). (See temperature setting table included in the user’s manual as a guide.)
4. The Steam Ready Indicator Light (2) will come on in 8-10 minutes indicating steam is available.
The Steam Ready Indicator Light (2) will go on and off while the generator is in use.
5. Press Steam Button (a) to activate the steam release.
NOTE: Trying to use steam before the Steam Ready Indicator Light (2) is “ON” can cause
water drops in the steam coming out of the iron.
4. CONTINUOUS STEAM LOCK-ON BUTTON:
If you need a steady steam supply, press the Steam Button (a) down and then push the Continuous
Lock-On button (b) backwards to lock the Steam Button (a) in. To unlock, press the Steam Button (a)
down again and push the Continuous Steam Lock-On Button (b) forwards.
NOTE: Before ironing, point iron away from table, press Steam Button (a) to clear initial condensation.
WARNING: Never direct steam from the iron at yourself or another person. Special care must be
taken when the iron is used in a vertical position. The steam is very hot and can cause
burns.
5
5. STEAM:
A. TO EMPTY/RELEASE STEAM FROM THE GENERATOR:
1. Press Iron On/Off Rocker Switch (4) into the “ON” position.
2. Press the “Steam On/Off Rocker Switch (1) into the “Off”
position.
3. Release all remaining steam in the steam generator by
pressing the “Steam Button” (a) on the iron.
4. Press the Iron ON/OFF Rocker Switch (4) into the “OFF”
position.
5. Unplug the appliance from the wall outlet. Allow it to cool a
minimum of 5 minutes. Make sure that both the Iron
ON/OFF Rocker Switch (4) and the Steam ON/OFF Rocker
Switch (1) are in the “OFF” position.
B. FILLING/REFILLING THE REMOVABLE WATER TANK (9) :
The tank can be filled/refilled using a bottle or similar object, or by taking it off the base
altogether. To fill it using a bottle, just open the rotating cap (10) and then replace the rotating
cap (10) after you have filled the water tank.
To fill/refill the removable water tank (9) by removing the tank from the base, proceed as
follows:
1. Release the Locking Device (8) on the removable water tank (9) and remove the water tank
by lifting it up.
2. Open the Rotating Cap (10) and fill with tap or demineralized/distilled water (maximum
capacity 2 1/2 cups/625 ml).
3. Re-close the Rotating Cap (10) and put the removable water tank (9) back on the Steam
Base Tank (7), pushing is down until the locking device (8) clicks.
4. Your appliance is now ready to use.
C. WHEN TO REFILL THE WATER TANK/STEAM GENERATOR:
For best results, refill water tank/steam generator to maximum before every usage, when
steam power is recognized lower while in use or when Water Level Indicator Light (3) goes
“On”. Follow the water filling/refilling instructions above.
6
D. TEMPERATURE SETTINGS:
• Always read garment labels and follow directions.
• For maximum efficiency, iron garments requiring the lowest temperature settings first as the
iron heats up faster than it cools.
• If there are no instructions included with the garment, we suggest that you follow the table
above as a guide (except when any fabric has an applied finish, gloss, etc. where lower
temperatures might be required).
• Always iron blends (fabrics made of two or more types of fibers) using the heat setting
appropriate for the fabric requiring the lowest temperature setting.
6. IMPORTANT PRESSING TIPS:
A. USE STEAM INTERMITTENTLY:
Your Steam Generator Iron features a professional type iron with steam holes placed in the
front of the iron soleplate. Correct ironing procedure involves steaming the fabric with the front
end of the iron followed by pressing and drying with heat from the rear of the iron. For best
results, garments should be dry after pressing to avoid re-wrinkling due to lingering dampness.
Therefore, we recommend that you use steam as required, but not continuously.
B. PRESSING DIFFICULT NATURAL FIBERS (I.E. 100% COTTON DRESS SHIRTS, ETC.):
While your Steam Generator offers high quality professional type steam, some fabrics may
require additional moisture for best results. You may want to press cotton shirts while still
damp or spray with demineralized/distilled water, prior to ironing.
7
C. DRY STEAM V.S. HUMID STEAM:
Because steam is produced in a generator and not in the iron (as with regular household irons)
you can select dry or humid steam. The temperature of the iron setting determines the type of
steam. At high temperatures, the iron delivers very dry steam. Lower temperature settings
(within steam range) offer humid steam.
D. USER BENEFITS:
For best pressing results, you have the flexibility to choose the type of steam and not only the
iron temperature.
A balance should be maintained between the humidity (low iron
temperature) required to loosen fibers and the need for heat (higher iron temperature) to
flatten/shape and dry the fibers.
Instructions for specific iron temperature settings should be treated as guidelines only. We
recommend that you experiment with each fabric. The EP8020 can produce humid steam at
relatively low temperature settings where regular household irons would release water. Also,
the very dry steam produced at high iron temperature setting (3 dots “ ”) can be used on
some fabrics where normally the use of steam is prohibited.
8
STORAGE/CLEANING AND MAINTENANCE
STORAGE:
• Always unplug the power cord from the wall outlet when not in use.
• Always store in a dry place away from children’s reach.
• Always drain the Removable Water Tank (9) before storing.
• Always let your ironing system cool completely before putting away.
• Do not allow the electrical cord and steam hose to touch hot surfaces.
• Wrap the cord loosely around the ironing system when storing.
CLEANING/MAINTENANCE:
• The cord must be unplugged from the wall outlet before starting to clean any part of the
appliance.
• Make sure that the Iron and Steam Generator are COLD before starting to clean. Allow at
least twelve (12) hours for the unit to cool after it has been used.
IRON:
• Clean the steam iron only when it is cold.
• Never immerse the steam iron in water or any other liquids.
• Do not use scouring pads, abrasives or harsh cleaners.
• Prepare a paste using mild scouring powder and a little water. Apply a small amount of the
paste to the soleplate with a damp cloth. Rub the soiled area and then wipe clean with a
clean damp cloth.
• If using soleplate cleaners, make sure that you follow label instructions.
• Use a soft cloth dampened with water and mild household detergent to wipe the outer shell
of the iron.
• Dry soleplate and iron shell thoroughly after cleaning.
STEAM GENERATOR/STEAM BASE TANK (7):
Thanks to the professional steam heating system
, which ensures that the heating
element never comes into contact with water, the elements cannot be damaged with mineral
deposits.
Nevertheless, if tap water is used in the appliance, it should be rinsed out on a regular basis.
This will extend the life and trouble-free use of the appliance.
1. Unplug the power cord (12) from the wall outlet.
2. Allow the appliance to cool down completely, approximately 12 hours.
3. Take off the removable water tank (9).
4. Unscrew the steam pressure valve (5) using the special key (13) included.
5. Fill the steam boiler with about 3.3 oz (100 ml.) of water and rinse the appliance out
thoroughly.
6. Before replacing the steam pressure valve (5), pour into the boiler 8 oz (250 ml.) of water.
9
TROUBLESHOOTING
Do not operate the ironing system with a damaged cord, plug or if the iron or any other part of
the system has been dropped or damaged. To avoid the risk of electric shock, do not
disassemble or attempt to repair the ironing system. Return the appliance to EURO-PRO
Operating LLC (see Warranty) for examination and repair. Incorrect re-assembly or repair can
cause a risk of electric shock or injury to persons when the ironing system is used.
POSSIBLE CAUSES
REMEDY
PROBLEM
1. Turn Steam ON/OFF Rocker
Switch “ON” .
No steam is released
through the iron
1. Steam ON/OFF Rocker Switch is
not in the “ON” position.
2. Fill with water as per instructions.
2. Water Tank/Steam Generator is
empty.
3. Unit is not plugged in.
4. Steam is not visible because the
temperature of the soleplate is at
maximum & room temperature is
high.
3. Make sure both Steam & Iron
ON/OFF Rocker Switches are in
the “OFF” position and plug unit
in.
4/5.The heating time for the generator
is approximately 8-10 minutes .
Watch for Steam Ready Light to
come on indicating that steam is
ready.
5. Generator is NOT fully heated.
1. Iron is not switched ON.
2. Temperature is set at “Minimum”.
1. Turn Iron ON/OFF Rocker Switch
“ON” .
The soleplate remains
cold
2. Turn the temperature dial to the
appropriate setting.
1. Soleplate temperature is too low
to iron with steam.
1. Turn the temperature dial to the
marks between 2 and 3 dots. .
Drops of water leak
from the iron soleplate
2. Generator is NOT fully heated.
2. Wait for generator to be fully
heated.
1. Residue in water tank.
2. Not using demineralized/distilled
water.
1. Clean steam generator as per
instructions.
2. Use demineralized/distilled water
after cleaning the tank.
Dirty or yellow steam is
coming out of the iron
1. Yellowing occurs with normal
aging.
Yellowing of generator
Excessive yellowing
1. Leaving iron idle on top of
generator at high temperature for
long periods of time.
10
Model EP8020
LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and workmanship for a
period of ONE (1) year from the date of purchase when utilized for normal household use by the original
purchaser only. The attached Warranty Registration Card which must be filled out and returned within 10 days
of purchase. This is essential for your Warranty to be effective should any problem arise with this product.
Should any defect covered by the terms of the limited warranty be discovered within ONE year, EURO-PRO
Operating LLC will repair or replace any defective part provided the unit is returned by the original purchaser,
freight prepaid, to EURO-PRO Operating LLC, 94 Main Mill Street, Door 16, Plattsburgh, NY 12901. Proof of
purchase date and $ 12.95 for handling and return packing/shipping charges must be included.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the replacement parts or the complete
unit at our option. LABOUR CHARGES ARE NOT INCLUDED.
This warranty does not cover normal wear of parts and apply to any unit that has been tampered with or used
for commercial purposes. This limited warranty does not cover damage caused by misuse, negligent handling
or damage due to faulty packaging or mishandling in transit (by any common courier).
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional
warranties. The responsibility of EURO-PRO Operating LLC , if any, is limited to the specific obligations
expressly assumed by it under the terms of the limited warranty. In no event is EURO-PRO Operating LLC
liable for incidental or consequential damages of any nature whatsoever. Some states do not permit the
exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
PURCHASER
DATE OF PURCHASE
DEALER
IMPORTANT: Carefully pack item to avoid damage
yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
OWNERS REGISTRATION CARD
FOR CANADIAN CONSUMERS ONLY
Please complete and return within ten (10) days of purchase in order to validate the foregoing Limited Warranty. The
registration will enable us to contact you in the event a product defect is discovered. By returning this card, you acknowledge
to have read and understood the instructions for use and warnings set forth in the accompanying instructions. RETURN TO:
U.S.:
EURO-PRO Operating LLC, 94 MAIN MILL STREET, DOOR 16, PLATTSBURGH, NY 12901
CANADA: EURO-PRO Operating LLC, 4400 BOIS FRANC, ST. LAURENT, QUEBEC H4S 1A7
PURCHASER:
ADDRESS:
CITY:
STATE/PROV:
MODEL:
DATE OF PURCHASE:
NAME & ADDRESS OF DEALER:
EP8020
Printed in Italy
|